How To Use A Drawer Lock Router Bit
I unlock the router plunge mechanism and adjust the bit. While the bit is very easy to use set-up is essentially trial and error.
Drawer Lock Joint Router Bit Woodworking Joints Woodworking Tips Router Bits
Next you set the fence so that the middle of the angled part of the bit.
How to use a drawer lock router bit. To set up adjust the depth of cut on the work piece being passed against the bit horizontally to be the same as the thickness of the other work piece. Simply attach the Lock Miter Master Jig to the lock miter router bit cutting edge. Insert the bit securely in a table-mounted router and set the bit height so the top cutting edge is 38 above the table.
To machine the door front set the fence 38 back from the outermost cutting edge of the bit. First make sure that your router is unplugged. 1 If your router table doesnt have a split fence youll need to build out the fence almost the full diameter of the.
A feather board is a must here. For better safety this bit should be used only in a router table equipped with a fence and not used free hand. The result is a strong efficient joint between the sides and front of a drawer.
It includes an advanced polymer friction-fit holder that can be mounted horizontally or upright. Use in table-mounted routers. You can easily re-use that mdf for the drawer lock bit next time.
The cleverly-designed Drawer Lock Bit produces both pieces of the drawer joint using a single bit. In your router table set the bit ¼ high with the fence positioned so the centre of the stock lines up with the middle of the 45 portion of the bit. Rout the drawer front 1.
I am delighted to say that when I tried your and Dave from Cave Creeks setup instructions for the lock joint bit I got good results. Ok now to make the sides. Mill extra stock the same thickness as your project stock use.
For better safety this drawer lock bit should be used only in a router table equipped with a fence and not used free hand. Use only in a table-mounted router at reduced RPMs. Router bit but the Lock Miter Master Jig will work with most major lock miter router bits available.
Then without adjusting the bit height the drawer side is routed with the work piece standing vertically. The key point I did not previously understand was the importance of the fence position for machining the sides of the drawers. Also I noticed the stock didnt have much support on the bottom so I clamped a scrap piece of wood to the inside of the drawer side.
Drawer fronts are formed horizontally flat on the table surface. To make a sacrificial fence clamp a suitable piece of 34 or 12 inch mdf to your fence with the fence placed behind the bit start the router and pull the mdf fence towards you into the bit until it comes all the way through. Both are limited to use with 14 shank router bits.
If your router permits raise the bit so that you can set the bottom edge of the cutter against a block as shown above. Each bit includes an advanced polymer friction-fit holder that can be mounted horizontally or upright. Drawer Lock Router Bits.
A single bit routs both parts of the joint and is capable of routing joints for drawers with applied drawer fronts and for drawer. Note the bit I am using has a 12 shaft and a total diame-ter of 2 inches. This was alittle tricky since the drawers are stickin straigh up in the air.
3 Calculate the fence position by adding your drawer. For that width I will set the router on a slower speed 18000 rpm is recommended by the manufacturer. As with other joinery bits we recommend making test.
Our Drawer Lock Bit routs a joint similar to a locking rabbet but the rabbet is wedge-shaped so the parts fit tighter when clamped. Youll feel the machined lip of the Lock Miter Master Jig lock into place as you slide it up the cutting edge. Exact fit over the bit next time is not required.
There are two methods one for drawers made of 12 wood which I am using and one for drawers made of 14 stock First the router bit is set to the depth of one quarter inch which is half the thickness of your stock. I start by installing the bit in the router. Now draw lines corresponding to the bits lower and upper edges on your router tables outfeed fence.
I used the Infinity Tools Lock Miter Sr. The bit bodies have a non-stick coating for easy resin removal. Routes hardwood softwood and composite materials.
Be sure to set the recommended speed that comes with your bit. 2 Mount the drawer-lock bit in your table-mounted router and set the top of the cutter so that its 1532 above the. How to use a Drawer-Lock Router Bit The drawer lock bit is designed to specifically to joint 12mm timber at a 90angle to improve joint strength and ease of assembly when making drawer frames.
Small Drawer Lock Bit.
1 4 Inch Shank Drawer Lock Joint Making Router Bit Key Hole Cutter For Wood Working Router Bits Router Bit Set Router
Router Bit Set Up Jigs For 92112 And 92123 Drawer Lock Bits Woodworking Tool Set Woodworking Saws Best Woodworking Tools
45 Degree Lock Miter Router Bit Modernindigo Router Bits Router Woodworking Joints
Pin On Woodwork
Pin On Tools
45degree Lock Miter Router Bit Woodwork Tenon Cutter Tool W 1 4inch Shank Router Bits Woodworking Tips Woodworking Tools
1 Drawer Lock Router Bit Rockler Woodworking Hardware Jet Woodworking Tools Woodworking Tools
Freud 99 240 Drawer Lock Router Bit 2 Dia X 33 64 H X 1 2 Shank Woodworkinghardware Router Bits Learn Woodworking Woodworking Saws
Axcaliber Drawer Lock Cutter 1 2 Shank Dove Tail Joints Hand Held Router Lock
Pin On Buy Drawer Lock Router Bits
Reversible Drawer Lock Glue Joint Bits Router Cabinets Styles Drawer Slides
1 Drawer Lock Router Bit Rockler Woodworking Hardware Woodworking Tools Wood Crafting Tools Woodworking Tools Storage
Pin On Woodworking
Lock Miter Router Bits Router Woodworking Woodworking Tips Woodworking Plans Boxes
Drawer Lock Router Bit 1 2 Shank Rockler Woodworking Tools Jet Woodworking Tools Woodworking Joints Woodworking Jigs
Router Bit Set Up Jigs Derevoobrabotka Prisposobleniya Dlya Derevoobrabotki Plotnickie Raboty
Create A Rabbeted Drawer Lock Joint Using A Slot Cutter Woodworking Tips Diy Drawers Joinery
1 Drawer Lock Router Bit Rockler Woodworking Hardware Router Bits Woodworking Easy Woodworking Projects
7 29 1 2 Inch Drawer Lock Joint Router Bit Reversible Drawer Joint Bit Milling Cutter Ebay Home G Router Bits Woodworking Router Bits Router Woodworking
